source: sasmodels/doc/guide/orientation/orientation.rst @ 5f8b72b

core_shell_microgelsmagnetic_modelticket-1257-vesicle-productticket_1156ticket_1265_superballticket_822_more_unit_tests
Last change on this file since 5f8b72b was eda8b30, checked in by richardh, 7 years ago

further changes to model docs for orientation calcs

  • Property mode set to 100644
File size: 3.9 KB

Oriented particles

With two dimensional small angle diffraction data SasView will calculate scattering from oriented particles, applicable for example to shear flow or orientation in a magnetic field.

In general we first need to define the mean, or a reference orientation of the particles with respect to the incoming neutron or X-ray beam. This is done using three angles: $theta$ and $phi$ define the orientation of the axis of the particle, angle $Psi$ is defined as the orientation of the major axis of the particle cross section with respect to its starting position along the beam direction. The figures below are for an elliptical cross section cylinder, but may be applied analogously to other shapes of particle.

Note

It is very important to note that these angles, in particular $theta$ and $phi$, are NOT in general the same as the $theta$ and $phi$ appearing in equations for the scattering form factor which gives the scattered intensity or indeed in the equation for scattering vector $Q$. The $theta$ rotation must be applied before the $phi$ rotation, else there is an ambiguity.

orient_img/elliptical_cylinder_angle_definition.png

Definition of angles for oriented elliptical cylinder, where axis_ratio b/a is shown >1, Note that rotation $theta$, initially in the $xz$ plane, is carried out first, then rotation $phi$ about the $z$ axis, finally rotation $Psi$ is around the axis of the cylinder. The neutron or X-ray beam is along the $z$ axis.

orient_img/elliptical_cylinder_angle_projection.png

Some examples of the orientation angles for an elliptical cylinder, with $Psi$ = 0.

Having established the mean direction of the particle we can then apply angular orientation distributions. This is done by a numerical integration over a range of angles in a similar way to polydispersity for particle size. In the current version of sasview the orientational dispersity is defined with respect to the axes of the particle.

The $theta$ and $phi$ parameters to orient the cylinder only appear in the model when fitting 2d data. On introducing "Orientational Distribution" in the angles, "distribution of theta" and "distribution of phi" parameters will appear. These are actually rotations about the axes $delta_1$ and $delta_2$ of the cylinder, the $b$ and $a$ axes of the cylinder cross section. (When $theta = phi = 0$ these are parallel to the $Y$ and $X$ axes of the instrument.) The third orientation distribution, in $psi$, is about the $c$ axis of the particle. Some experimentation may be required to understand the 2d patterns fully. A number of different shapes of distribution are available, as described for polydispersity, see :ref:`polydispersityhelp` .

?

Earlier versions of SasView had numerical integration issues in some circumstances when distributions passed through 90 degrees. The distributions in particle coordinates are more robust, but should still be approached with care for large ranges of angle.

Note that the form factors for asymmetric particles are also performing numerical integrations over one or more variables, so care should be taken, especially with very large particles or more extreme aspect ratios. Users can experiment with the values of Npts and Nsigs, the number of steps used in the integration and the range spanned in number of standard deviations. The standard deviation is entered in units of degrees. For a rectangular (uniform) distribution the full width should be $pmsqrt(3)$ ~ 1.73 standard deviations (this may be changed soon).

Where appropriate, for best numerical results, keep $a < b < c$ and the $theta$ distribution narrower than the $phi$ distribution.

Some more detailed technical notes are provided in the developer section of this manual :ref:`orientation_developer` .

?

Document History

2017-10-27 Richard Heenan
Note: See TracBrowser for help on using the repository browser.