-                      r6aad2e8
+                      r094b9eb
 -----------
 The scattering, or Porod, invariant (Q*\) is a model-independent quantity that
+The scattering, or Porod, invariant ($Q^*$) is a model-independent quantity that
 can be easily calculated from scattering data.
 For two phase systems, the scattering invariant is defined as the integral of
 the square of the wave transfer (Q) multiplied by the scattering cross section
 over the full range of Q from zero to infinity, that is
+For two phase systems, the scattering invariant is defined as the integral of
+the square of the wavevector transfer ($Q$) multiplied by the scattering cross section
+over the full range of $Q$ from zero to infinity, that is
 .. image:: image001.png
+.. math::
+where *g = q* for pinhole geometry (SAS) and *g = q*\ :sub:`v` (the slit height) for
+slit geometry (USAS).
+    Q^* = \int_0^\infty q^2I(q)\,dq
+The worth of Q*\  is that it can be used to determine the volume fraction and
+the specific area of a sample. Whilst these quantities are useful in their own
+in the case of pinhole geometry. For slit geometry the invariant is given by
+.. math::
+    Q^* = \Delta q_v \int_0^\infty qI(q)\,dq
+where $\Delta q_v$ is the slit height.
+The worth of $Q^*$  is that it can be used to determine the volume fraction and
+the specific area of a sample. Whilst these quantities are useful in their own
 right they can also be used in further analysis.
 The difficulty with using Q*\  arises from the fact that experimental data is
 never measured over the range 0 =< *Q* =< infinity. At best, combining USAS and
 WAS data might cover the range 1e-5 =< *Q* =< 10 1/\ |Ang| . Thus it is usually
 necessary to extrapolate the experimental data to low and high *Q*. For this
+The difficulty with using $Q^*$  arises from the fact that experimental data is
+never measured over the range $0 \le Q \le \infty$. At best, combining USAS and
+WAS data might cover the range $10^{-5} \le Q \le 10$ 1/\ |Ang| . Thus it is usually
+necessary to extrapolate the experimental data to low and high $Q$. For this
 High-*Q* region (>= *Qmax* in data)
+High-\ $Q$ region (>= *Qmax* in data)
 *  The power law function *C*/*Q*\ :sup:`4` is used where the constant
    *C* (= 2.\ |pi|\ .(\ |bigdelta|\ |rho|\ ).\ *Sv*\ ) is to be found by fitting part of data
    within the range *Q*\ :sub:`N-m` to *Q*\ :sub:`N` (where m < N).
+*  The power law function $C/Q^4$ is used where the constant
+   $C = 2 \pi \Delta\rho S_v$ is to be found by fitting part of data
+   within the range $Q_{N-m}$ to $Q_N$ (where $m < N$).
 Low-*Q* region (<= *Qmin* in data)
+Low-\ $Q$ region (<= *Qmin* in data)
 *  The Guinier function *I0.exp(-Rg*\ :sup:`2`\ *Q*\ :sup:`2`\ */3)* where *I0*
    and *Rg* are obtained by fitting as for the high-*Q* region above.
+*  The Guinier function $I_0 exp(-R_g^2 Q^2/3)$ where $I_0$
+   and $R_g$ are obtained by fitting as for the high-\ $Q$ region above.
    Alternatively a power law can be used.
 …
 ) Load some data with the *Data Explorer*.
 ) Select a dataset and use the *Send To* button on the *Data Explorer* to load
+) Select a dataset and use the *Send To* button on the *Data Explorer* to load
    the dataset into the *Invariant* panel.
 ) Use the *Customised Input* boxes on the *Invariant* panel to subtract
    any background, specify the contrast (i.e. difference in SLDs - this must be
    specified for the eventual value of Q*\  to be on an absolute scale), or to
+) Use the *Customised Input* boxes on the *Invariant* panel to subtract
+   any background, specify the contrast (i.e. difference in SLDs - this must be
+   specified for the eventual value of $Q^*$  to be on an absolute scale), or to
    rescale the data.
 ) Adjust the extrapolation range as necessary. In most cases the default
+) Adjust the extrapolation range as necessary. In most cases the default
    values will suffice.
 ) Click the *Compute* button.
 ) To include a lower and/or higher Q range, check the relevant *Enable
+) To include a lower and/or higher $Q$ range, check the relevant *Enable
    Extrapolate* check boxes.
    If power law extrapolations are chosen, the exponent can be either held
    fixed or fitted. The number of points, Npts, to be used for the basis of the
+   If power law extrapolations are chosen, the exponent can be either held
+   fixed or fitted. The number of points, Npts, to be used for the basis of the
    extrapolation can also be specified.
 ) If the value of Q*\  calculated with the extrapolated regions is invalid, a
+) If the value of $Q^*$  calculated with the extrapolated regions is invalid, a
    red warning will appear at the top of the *Invariant* panel.
    The details of the calculation are available by clicking the *Details*
+   The details of the calculation are available by clicking the *Details*
    button in the middle of the panel.
 …
 ^^^^^^^^^^^^^^^
 The volume fraction |phi| is related to Q*\  by
+The volume fraction $\phi$ is related to $Q^*$  by
 .. image:: image002.png
+.. math::
+where |bigdelta|\ |rho| is the SLD contrast.
+    \phi(1 - \phi) = \frac{Q^*}{2\pi^2(\Delta\rho)^2} \equiv A
+.. image:: image003.png
+where $\Delta\rho$ is the SLD contrast.
+.. math::
+    \phi = \frac{1 \pm \sqrt{1 - 4A}}{2}
 .. ZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZ
 …
 ^^^^^^^^^^^^^^^^^^^^^
 The specific surface area *Sv* is related to Q*\  by
+The specific surface area $S_v$ is related to $Q^*$  by
 .. image:: image004.png
+.. math::
+where *Cp* is the Porod constant.
+    S_v = \frac{2\pi\phi(1-\phi)C_p}{Q^*} = \frac{2\pi A C_p}{Q^*}
+where $C_p$ is the Porod constant.
 .. ZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZ

Note: See TracChangeset for help on using the changeset viewer.

SasView

Changeset 094b9eb in sasview for src/sas/sasgui/perspectives

Legend:

src/sas/sasgui/perspectives/invariant/media/invariant_help.rst

Download in other formats: